Forums 168 results

1,731 views, 0 by Moke

Add a Table Top Drill Press?

For some reason I have been looking at adding a table top DP. Keep in mind I have a very nice, but older Craftsman DP that was my second woodworking tool, 30+ years ago. It works well but is in the corner of my shop and sometimes has stuff in...

1,289 views, 0 by Blackie

Blackie

Lowering your Table Saw Blade

I have a couple questions on lowering your table saw blade. 1. How many of you lower your table saw blade beneath the table once you’re done working with it? 2. What is your reason for lowering the blade? This week I was working on a box,...

1,169 views, 0 by MsDebbieP

MsDebbieP

TIPS: safety on the table saw

what are your TIPS for (safely) using the table saw

1,350 views, 0 by Glaros Studios

Glaros Studios

Sliding Table saws

I’m thinking of buying a sliding table (panel) saw. Anyone familiar with these? I haven’t used them before. There is a Grizzly saw for sale (grizzly G0623X3) for $3250 Cdn but comes with a roto phase so I can actually use it. New panel saws are...

1,386 views, 0 by MontyJ

MontyJ

Table saw question

I have a Grizzly 1022z. Today I was going to use it to cut 45° miters on a box. Out of curosity, I decided to check the blade to miter slot parallelism. With the blade at 90° it’s within .001. When I tilted the blade and checked it it was out by...

1,865 views, 0 by Jeff B

Jeff B

table saw blade flex

Hey, I’ve been noticing that when I’m cutting 45 degree beveled cuts on my table saw for glued miter joints that in the last few inches of the cut my table saw blade seems to be flexing a bit creating a concave surface on the beveled face of the...

1,106 views, 0 by Martin Sojka

Martin Sojka

Vintage Tables

See these amazing tables by the Vintage Industrial

1,378 views, 0 by Bill T

New Table saw

Starting to look around at upgrading my table saw ( the one I have is a old Beaver saw Its about 45 years old I remember my dad having it when I was a kid many moons ago) its a belt drive will take a 8" blade no guards of course and top is approx...

1,508 views, 1 by TonyCan

TonyCan

Movable work table

So i work out of my garage and needed a table that could house most of my tools and be movable. So i made this. I started out with the bottom frame, basic 2×4′s Then i made the top frame, but for this i did not put 2×4′s on the ends, just...

554 views, 0 by Jack

Jack

Dining table top grain question

I am building a dining room table with a top of approximately 44” by 65”. The bottom will be painted with lamp black milk paint and the top will be oak with only clear topcoat. I have a supply of beautiful oak just the right length to make the...

1,019 views, 0 by Kelly

TABLE SAW LONG PIECE CUTTING JIG

I have a Unisaw with a 52" fence. Needless to say, cutting a forty-five on 3/4" stock longer than its capabilities is a challenge. I could run against a sacrificial fence, but that requires me to rely on the cut portion, in back of the blade,...

872 views, 0 by Brian

Brian

table saw tune-up

My saw has been a little out of whack for a few months. A few issues. First the fence was not plumb. I thought one of the glide pads was worn down but it turned out to be a warped table causing it. Not the table actually, but the fence rails. I...

858 views, 0 by Kelly

L-square Stop - Depth Gauge - Table Saw Setup Tool

This tool serves several functions. It can be used as: - an edge stop for L-squares; - a wide gap depth gauge; and, - as a set up tool for table saws. This tool allows the user to, easily, lay out lines at ninety degrees...

791 views, 0 by Martin Sojka

Martin Sojka

Inspiration: 20 Unique Coffee Tables

Some really unique coffee table designs. Hope you find an idea or two for your next coffee table project :)

552 views, 0 by mrwojo

radiant floors and dinning table

Good afternoon. I am building a 4×8 x21/4 single slab live edge pine farm table for my wife . The wood is approx 8% moisture as it sits in the shop . My question relates to radiant heat and this table . My house is heated with radiant floors with...

750 views, 0 by TonyCan

TonyCan

Table advice

I was asked to build this, but not sure on the finish, what do you think that finish is and what kind of wood would you use? Don’t go to expensive on me.

2,840 views, 1 by Kelly

Table Saw Set-up Gauge

I designed this guide back in the eighties, to allow me to be sure my table saw top was positioned exactly ninety degrees to the blade, and for setting up cuts on my, then, less than reliable fence. A table saw blade must be perfectly ninety...

781 views, 0 by FlagshipOne

Grizzly G0715P 10" hybrid table saw.

Need a bit of help …. I have a Grizzly G0715P 10" hybrid table saw. I am attempting to align the miter slot to the blade but am having difficulty. I am using a dial indicator made by Woodpeckers for measurements but cannot seem to get it any...

2,761 views, 0 by Kelly

Powermatic Band Saw Extension Table

I’ve made several 30” circles using my circle cutting jig. Each time, it’s been a struggle holding the right side of the jig, with the material on it, flush with the table. I thought about making a cart, but that seemed like a lot of material,...